2017 June Cisco Official New Released 300-101 Dumps in Lead2pass.com!
100% Free Download! 100% Pass Guaranteed!
We never believe in second chances and Lead2pass brings you the best 300-101 Exam Questions which will make you pass in the first attempt. We guarantee all questions and answers in our 300-101 Dumps are the latest released, we check all exam dumps questions from time to time according to Cisco Official Center, in order to guarantee you can read the latest questions!
Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/300-101.html
Which type of access list allows granular session filtering for upper-level protocols?
A. content-based access lists
B. context-based access lists
C. reglexive access lists
D. extended access lists
Which three configuration parameters can a DHCPV6 pool contain? (Choose three.)
A. domain search list
B. router IP
C. default gateway
D. prefix delegation
E. DNS servers
F. subnet mask
Which statement about local policy routing is true?
A. It is used to policy route packets that are generated by the device.
B. It requires all packets to be packet switched.
C. It is used to policy route packets that pass through the device.
D. It requires all packets to be CEF switched.
E. It supports IPv4 packets only.
F. It requires an ip address or access list as the matching criteria.
Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?
A. show snmp group
B. show snmp user
C. show snmp
D. show snmp view
Which type of information is displayed when a network engineer executes the show track 1 command on the router?
A. information about tracking list 1.
B. time to next poll for track object 1.
C. information about the IP route track table.
D. tracking information statistics.
Which command sequence can you enter on a router to configure Unicast Reverse Path Forwarding in loose mode?
A. interface GigabitEthernet0/0
ip verigy unicast source reachable-via all
B. interface GigabitEthernet0/0
ip verigy unicast source reachable-via loose
C. interface GigabitEthernet0/0
ip verigy unicast source reachable-via any
D. interface GigabitEthernet0/0
ip verigy unicast source reachable-via rx
Where can NetFlow export data for long term storage and analysis?
C. another network device
D. flat file
Which option is the first task that a device that is configured with NAT64 performs when it receives an incoming IPv6 packet that matches the stateful NAT64 prefix?
A. It translates the IPv6 header into an IPv4 header.
B. It checks the IPv6 packet against the NAT64 stateful prefix.
C. It translates the IPv6 source address to an IPv4 header.
D. It translates the^ IPv4 destination address into a new NAT64 state.
E. It performs an IPv6 route lookup.
Which command do you enter to display log messages with a timestamp that includes the length of time since the device was last rebooted?
A. service timestamps log uptime
B. logging facility 20
C. service timestamps debugging localtime msec
D. logging console errors
E. logging monitor 7
F. service timestamps log datetime msec
Which option must be configured on a target device to use time stamping to accurately represent response times using IP SLA?
B. Jitter value
C. TCP Connect
D. ICMP Echo
Refer to the exhibit. Which option describes why the EIGRP neighbors of this router are not learning routes that are received from OSPF?
A. The subnet defined in OSPF is not part of area 0.
B. Default metrics are not configured under EIGRP.
C. There is no overlap in the subnets advertised.
D. The routing protocols do not have the same AS number.
Which two options are requirements for EIGRP authentication? (Choose two)
A. A crypto map must be configured.
B. The Authentication key must be configured under the interface running EIGRP.
C. The authentication key must be configured within the EIGRP routing configuration.
D. The authentication key IDs must match between two neighbors.
E. A separate key chain must be configured.
F. AN IPsec profile must be configured.
A network engineer is troubleshooting connectivity issues with a directly connected RIPng neighbor. Which command should directly connected RIPng neighbor adjacencies only?
A. router#show ipv6 rip next-hops
B. router#show ip rip neighbors
C. router#show ipv6 routers
D. router#show ipv6 rip database
Which security feature can you enable to control access to the vty lines on a router?
A. exec-time out
C. username and password
D. transport output
A network engineer wants an NTP clients to be able to update the local system without updating or synchronizing with the remote system.
Which option for the ntp access-group command is needed to accomplish this?
Lead2pass new released 300-101 PDF are now for free download, download it right now and pass your exam 100%.
300-101 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDbDJFcVRBc3pSdXc
2017 Cisco 300-101 exam dumps (All 332 Q&As) from Lead2pass:
http://www.lead2pass.com/300-101.html [100% Exam Pass Guaranteed]
|One Time Purchase||✔||✖||✖||✖||✖|
|100% Pass Guarantee||✔||✖||✖||✖||✖|
|100% Money Back||✔||✖||✖||✖||✖|